 |
 |
 |
 |
 |
 |
| Frame Post Reinforcement | ||
 |
Increases axial capacity of the frame and provides greater local impact resistance. |  |
|
Is standard on slant and set back let pallet frames. | |
|
Add + FR_XX to frame part number for front post reinforcement where XX is the height in inches. Add + RR_XX to frame part number for rear post reinforcement where XX is the height in inches. | |
| Bull Nose Deflectors/Angle Deflectors for Front Frame Posts | ||
|
Provide local impact resistance for front frame posts. | |
|
Factory welded | |
|
Standard lengths are 6". Custom lengths can be specified for the angle protector. Bull nose lengths must be specified in increments of 6" | |
|
Add + AD_XX for angle deflector where XX is the height in inches. | |
|
Add + BN_XX for bull nose where XX is the height in inches. | |
 |
 |
| Debris Caps for Box Post, Angle Protector, and Bull Nose (Optional) |  |
|
|
Are factory welded to keep debris and trash out of enclosed areas (Highly recommended for grocery rack storage) | |
|
Add + CAPS to frame part numbers. This will signify any reinforcement or deflector will have a cap. | |
|
Add + PCAP to frame part numbers in addition to + CAPS for bull nose plastic cap cover. | |
| Row Spacers | ||
|
Connects back to back pallet frames and monoposts. | |
|
Maintains spacing between frames for easy installation. |  |
|
Requires 4-1/2" Grade 5 bolts. | |
| Row Spacer Part No. = RS-48 where 48 is the length in inches between frames or monopost | ||
| Heavy Horizontal | ||
|
Replaces first horizontal angle web from the floor with channel. | |
|
Commonly used in drive-in applications. | |
|
Add + HH to frame part number. | |
| Monopost (Punched Single Channel Post with Foot Plate) | |||
|
Used in conjunction with pallet frames for multiple deep systems. | ||
|
Add + R_XX, where XX is the length in inches, for box reinforcement. |  |
|
|
Add + CAPS for reinforcement debris cap. | ||
| Monopost Part No. = MP-C3X4.1-216 where C3X4.1 = size and 216 = height in inches | |||
| Rub Rail | |||
|
Used as a continuous barrier near ground level between two frames (back to back) with heavy horizontals. | ||
|
Commonly used in drive-in applications. | ||
|
Requires 4-1/2" Grade 5 bolts | ||
| Rub Rail Part No. = RRA - 48 where 48 is the length between frames | |||
| Cross Aisle Tie (CAT) | |||
|
Connects cross aisle pallet frames for lateral stability requirements for excessive pallet frame height to depth ratios. |  |
|
|
Requires 4-1/2" Grade 5 bolts. | ||
| CAT Part Number: CAT-48 where 48 is cross aisle length in inches | |||
| Custom Foot Plates | |||
|
The standard 3/8" foot plate is depicted below. Any foot plate that does not match the thickness and hold pattern of the one below is considered custom. | ||
|
If need arises due to design concerns, the Hancock Rack engineering department will custom design the foot plate with different anchorage patterns, hold diameters, etc. | ||
|
Our 3/8" thick footplate provides superior load distribution into concrete slab |
 |
||
| Galvanized Shims |  |
||
|
Used to level and plumb pallet frames on uneven concrete slabs. | ||
|
Will match the hole pattern in the footplate. | ||
|
Are provided in 10 Gage or 16 Gage. | ||
| Shim Part No. = SHIM-16 where 16 = Gage | |||
| 1/2" Wedge Anchors | |||
|
Provide the required anchorage of pallet frames to the concrete slab. | ||
|
Require minimum embedment of 3-1/2". | ||
| Be sure your concrete slab is thick enough to achieve minimum embedment. | |||
|
Wedge Anchor Part No. = WA-1/2 where 1/2 = diameter in inches |
|||
 |
|||
